Changing brake discs on a motorcycle

When riding in traffic, good brakes are quite simply a matter of life or death. Which is why it's vital that every biker regularly checks their brakes – and that means more often than just the vehicle safety inspection required by law once every two years.

[HEADER: Changing brake discs on a motorcycle.]

Checking motorcycle brake discs for wear

Proper maintenance of your braking system includes changing old brake fluid, replacing worn brake pads and checking the brake discs. Every brake disc has a minimum thickness specified by the manufacturer, and when this service limit is reached, the disc must be replaced. You should check this with a micrometer, not a caliper gauge, because wear and tear causes the brake disc to form a small ridge at its outer edge which would falsify the measurement if you use a caliper gauge.

However, exceeding the thickness service limit is not the only reason for changing a brake disc. During heavy braking, the discs reach temperatures of up to 600°C. Temperature differences between the outer ring and inner carrier of the brake disc in particular produce uneven thermal expansion, which can cause the disc to distort. Extreme temperatures are not just a factor in racing, but also in normal, day-to-day biking. Travelling downhill on a mountain pass, where you're using your brakes constantly (often with heavy luggage and a pillion passenger), can push temperatures to mind-boggling heights. Sticking brake caliper pistons often generate high temperatures, and the constant contact with the brake pad can cause discs to wear extremely quickly. This can also cause discs to distort – a problem that particularly applies to discs with a large diameter and those that are rigidly mounted.

On modern motorcycles, the low-cost rigid discs tend to be used where the loads on the brake are relatively low. Today, the state of the art is floating brake discs on the front axle. These offer the following advantages:

  • Reduced rotating mass enhances handling
  • Less unsprung mass
  • Better adaptation of the materials to the demands made on them
    More spontaneous brake response
  • Less tendency for the brake disc to warp

Floating discs have an inner ring which is bolted to the wheel hub and connected by movable floaters (a.k.a. bobbins) to the outer ring, which the brake pads press against during braking. If the axial play of this connection exceeds 1 mm, the brake disc will rattle, which is when it needs replacing. Any type of radial play generates a type of "run-on" when braking and will also cause your bike to fail the vehicle safety inspection.

Important: Read the instructions before you pick up any tools!

Double check that the disc you have purchased is approved for your specific bike and application according to the accompanying type approval. Only use the suitable tools for installing the disc. Always use a torque wrench to ensure that the screws of the brake disc and the caliper are correctly tightened.

To make sure you have the correct torque and model-specific data for your braking system, always consult a workshop manual for your motorcycle model or ask your local authorised dealer. You should only do work on your braking system, following the instructions below, if you are an experienced DIY mechanic. Don't put your safety at risk! If you're not sure you're able to do the job, definitely leave it to the professionals!

[IMAGE: bike jack up.]
Jack up the bike and loosen the brake caliper

Changing a brake disc – step-by-step instructions

Loosen the brake caliper

First jack up your motorcycle securely in order to unload the wheel you are working on. If your bike is not fitted with a centre stand, you will need to use a paddock stand. Release the brake caliper(s) from the mount and replace the brake pads as described in the Tips for DIY mechanics, "Brake pads". Secure the brake caliper with wire to a part of the bike where it won't get in the way while you're removing the wheel – don't let it dangle on the brake hose.

[IMAGE: wheel axle.]
Loosen the wheel axle and remove the wheel

Remove the wheel

Loosen the wheel axle and remove the wheel from the front fork/rear wheel swing arm.

[IMAGE: fastening bolts.]
Undo the fastening bolts on the brake disc

Release the old brake disc

Lay the wheel on a suitable surface and undo the fastening bolts of the brake disc in diagonally opposite sequence. Always use quality tools that fit well, particularly if the hexagon socket screws are proving stubborn, and make sure that you insert the tool as far into the socket as possible to ensure a secure grip. If you strip the screw head so that no tool grips, removing the screw is going to be a real headache. If the screws prove very hard to shift, warming them and giving the tool a knock with a hammer can often help. If the hexagon socket of the screw head is stripped, you may be able to undo it by using a bit that is one size bigger and hammering it in so that it grips.

[IMAGE: old brake disc.]
Remove the old brake disc

Remove the old brake disc

Take the old brake disc(s) off the hub and clean the contact surface. You need to remove any unevenness (residual paint or Loctite, etc.), and this is also a good opportunity to clean the rim and axle, as access is easier.

[IMAGE: new brake disc.]
Fit new brake disc and fasten securely

Fit the new brake disc

Fit the new brake disc(s). Tighten the fastening bolts to the torque specified by the vehicle manufacturer, in diagonally opposite sequence. Always replace badly corroded or damaged fastening bolts with new ones.

Important: If the manufacturer recommends the use of threadlock adhesive, apply this sparingly and carefully. Under no circumstances must the threadlocker be allowed to run under the contact surface of the brake disc, as this may impair the parallelism of the disc, which in turn can cause the brakes to rub. Install the wheel and brake caliper in reverse order. If working on the front wheel, pay attention to the running direction of the tyre.

[IMAGE: checking brake and wheel.]
Check brake and wheel

Before actuating the handbrake cylinder, make sure that there is enough space in the brake fluid reservoir for the fluid level to rise. New pads and discs push the fluid upwards in the system, and you must make sure it doesn't exceed the "Maximum" mark. Actuate the main brake cylinder in order to bring the brake pads into contact with the disc. Check the pressure point of the brake. Check that the wheel turns freely once you have released the brake. If the brake drags, you may have fitted it incorrectly or the brake pistons may be sticking in the brake caliper.

Warped brake disc – troubleshooting

If you need to replace a brake disc due to warping, you should also check for the following potential problems, which can cause the disc to distort because the brake disc may not be parallel to the brake pistons in the caliper:

  • Is the front wheel fork adjusted correctly/without any misalignment?
  • Is the braking system correctly assembled (brake calipers original and suitable for your bike, and properly aligned with the brake disc)?
  • Are the brake discs in absolutely even contact with the hub (residual paint/Loctite could cause an uneven contact surface)?
  • Is the wheel correctly aligned on the wheel axle and in the centre of the front fork?
  • Is the tyre pressure correct?

But exceeding the thickness service limit of the brake disc, or the disc being warped, or the floaters worn are not the only reasons for replacing the brake disc. A badly scored surface also reduces braking performance noticeably – and again the only solution is to replace the brake disc. If your bike is fitted with dual disc brakes, you should always replace both brake discs at the same time. Similarly, in order to achieve optimum braking performance with a new brake disc, always replace the brake pads at the same time. Even if the old pads are still above the service limit, you still need to replace them, as their surface has adapted to the wear pattern of the old disc and would not be a snug fit with the new one – this would negatively affect braking performance and the new disc would wear down faster.

[IMAGE - Download this tip.]

Download this tip

For the garage: Simply download, print out and take it with you.

[IMAGE: the experts.]

The Louis Technical Centre

Problems getting spare parts? Or maybe you've got a technical question about your motorcycle or an accessory The Louis Technical Centre can help! Remember to quote all the necessary details of your vehicle – better still, send us a copy of your registration document.

We will get back to you as quickly as possible!

So: send us your technical problem!

Please note!

These tips for DIY mechanics contain general recommendations that may not apply to all vehicles or all individual components. As local conditions may vary considerably, we are unable to guarantee the correctness of information in these tips for DIY mechanics.

Thank you for your understanding.

[IMAGE - Buy the Louis Mechanic Manual now.]

German Version

Louis DIY Mechanic Manual

The printed version

The big Louis DIY mechanic manual available in a printed version: in color and practical A4 format at cost price.

Buy now!